What Textile Mills Should Specify Before Requesting Auxiliary Quotes?

A request for “a low-foam wetting agent” or “a softener for cotton” rarely provides enough information for a comparable quotation. Products that fit the same description can differ in concentration, compatibility, application conditions, and treatment cost.

Before requesting textile auxiliary quotes, mills should specify the substrate, process conditions, performance targets, chemical restrictions, and order requirements. These details help suppliers recommend an appropriate grade and make quotations easier to compare.

Auxiliary Requirements

Process Stage and Required Function

Start by identifying where the product will be used: pretreatment, dyeing, printing, afterwashing, or finishing. Then describe its job within that stage.

When sourcing textile auxiliaries, a functional description is more useful than a broad product name. For example, a wetting agent for high-alkali cotton pretreatment has different requirements from one used in a finishing bath.

State whether you need a single-function product, a combined formulation, or a replacement. For a replacement, provide the current product’s technical data and identify which results must be maintained.

Current Problem and Target Performance

Describe the problem and when it occurs, such as excessive foam during jet circulation or uneven softness after drying.

Include the current dosage, relevant observations, and any production limits. If the mill cannot add another rinse, increase the treatment temperature, or extend the cycle, say so before requesting a recommendation.

Textile Specifications

Fiber Composition and Blend Ratio

Provide the exact fiber composition and blend percentages. Cotton, polyester, nylon, viscose, and their blends place different demands on an auxiliary. Include elastane where present, even at a low percentage, because its presence can affect product selection and acceptable processing conditions.

Identify whether the material is fiber, yarn, knitted fabric, woven fabric, or a finished garment. Include the intended end use when it affects the requirements. A towel and a woven shirting fabric may both be cotton, but their finishing priorities differ.

Fabric Construction, Weight, and Pretreatment Status

For fabric applications, specify the construction and weight in g/m². Add details such as pile, compactness, or stretch where they influence penetration or handling. For yarn processing, provide yarn count and package details when relevant.

Describe the material’s condition when it reaches the relevant process. Note whether it has been desized, scoured, bleached, heat-set, dyed, or finished. Report known residual oils, alkali, or previous finishes rather than assuming the incoming fabric is chemically neutral and ready for treatment.

Process Conditions

Machinery and Application Method

Identify the machinery and whether processing is batch or continuous. Include loading and circulation conditions for batch equipment, or line speed for continuous processing. These details help establish the mechanical conditions and available treatment time.

Temperature, pH, and Treatment Time

Share the operating range and process sequence rather than only the peak temperature. Include heating and cooling rates, holding times, and any drying or curing conditions relevant to the treatment.

Specify the working bath pH. The pH measured in a diluted product sample on a technical data sheet does not establish the suitable pH range for your application.

Liquor Ratio or Wet Pickup

For exhaust processes, report the liquor ratio and define the dosage basis: g/L, percentage on the weight of fabric (% owf), or another stated basis. Identify whether the dosage refers to the product as supplied or to active material.

For example, at a liquor ratio of 1:10, 1 g/L corresponds to 10 g of product per kilogram of fabric, or 1% owf. At 1:5, the same 1 g/L corresponds to 0.5% owf. This calculation compares product quantities, not performance.

For padding, provide the target wet pickup and bath concentration.

Water Quality

Supply recent process water data where available, especially hardness and pH. State the units and reporting basis, such as mg/L as calcium carbonate for hardness. Include conductivity and relevant metal content if available, particularly when investigating deposits or shade variation.

Mark unknown values rather than supplying estimates as measured data.

Compatibility Requirements

Dye Class and Chemicals Used

Identify the dye class, such as reactive, disperse, or acid dyes, and provide relevant shade depth information. List the chemicals that will share the bath, including their dosages and order of addition. Include their ionic character where known, since some combinations of anionic and cationic products may cause instability.

Include preceding or subsequent treatments where chemical carryover is possible.

Foam Control and Chemical Stability

Define the conditions the product must tolerate. Depending on the application, these may include alkali, electrolyte, elevated temperature, or mechanical shear.

Set foam limits that reflect circulation, fabric transport, or filling requirements. A static laboratory observation may not predict behavior under production circulation.

Ask the supplier to identify application limits, including required dilution and any restrictions on mixing or addition sequence.

Effects on Shade, Fastness, and Handle

State which fabric properties must be preserved. Relevant requirements may include shade, whiteness, absorbency, stretch recovery, and colorfastness.

For textile softeners, define the required handle, absorbency, and acceptable shade change. A reference fabric helps make subjective handle descriptions more consistent.

For cotton finishing that requires both softness and hydrophilicity, Sylic F3230 Hydrophilic Block Silicone Softener provides a concrete specification example: it is cationic, has 48–50% solids, and has reference dosages of 10–30 g/L for padding or 3–5% owf for exhaust application. These ranges provide a trial starting point, not a guaranteed production dosage. Its cationic character makes compatibility with anionic bath components a specific check before approval; absorbency and shade must also be verified on the intended fabric.

Acceptance Criteria

Required Results and Test Methods

Define the test method, conditions, and acceptance threshold for each required result.

Requirement What to define before the trial
Wetting performance Test procedure, bath conditions, and acceptable wetting time
Foam behavior Test setup and acceptable foam level or collapse time
Handle Approved reference fabric and assessment procedure
Absorbency Test method and target after the specified treatment
Shade and fastness Assessment methods, tolerances or grades, and any washing or finishing before testing

Reference Samples and Trial Conditions

Provide material representative of the stage being tested and an approved finished sample where available. Identify whether evaluation will use laboratory or production equipment.

Agree on the starting dosage and trial conditions before samples are tested. Use the current product as a control where appropriate, keeping the substrate and other process variables consistent.

Record differences between the laboratory setup and production, including liquor ratio, agitation, heating rate, and drying conditions. A successful laboratory trial supports further evaluation but does not establish production-scale performance on its own.

Compliance Requirements

Customer and Destination-Market Restrictions

Send the chemical requirements that apply to the intended order. Identify the customer specification, applicable version, destination market, and end use rather than requesting a broadly “compliant” product.

Distinguish restrictions on manufacturing chemicals from limits on substances in finished textiles. For example, the ZDHC Manufacturing Restricted Substances List addresses chemical inputs used in manufacturing, while finished-product restricted substances lists address the resulting article. Evidence relating to one does not automatically establish conformity with the other.

Required Technical Data, SDS, and Conformance Evidence

State which documents must accompany the quotation and which are required before purchase. Specify the purpose of each document:

  • Technical data sheet (TDS): product characteristics, application guidance, and recommended operating conditions.
  • Safety data sheet (SDS): hazard information and handling, storage, and emergency guidance.
  • Conformance evidence: documentation addressing the applicable chemical requirements for the quoted grade.
  • Batch quality documentation: agreed release limits and a certificate of analysis (COA), where required for deliveries.

Check that supporting documents identify the exact quoted grade and that the evidence is valid and covers the applicable requirements.

Order and Delivery Details

Trial Quantity and Expected Order Volume

Separate the sample requirement, first commercial order, and expected repeat demand. State whether future volumes are confirmed or estimated.

Request the recommended dosage with the price and compare chemical cost per metric ton of fabric at dosages that meet the same acceptance criteria.

For example, a product priced at $2.00/kg and used at 2% owf costs $40 per metric ton of fabric. A product priced at $3.00/kg and used at 1% owf costs $30. These illustrative figures cover the auxiliary alone and assume equivalent acceptable results.

Account separately for any changes in rinsing, energy use, cycle time, or reprocessing demonstrated during trials.

Packaging, Destination, and Delivery Date

Specify the preferred package size, delivery location, and required arrival date. Include storage constraints, shelf-life requirements, or handling limitations that could affect the choice of product or packaging.

Clarify whether the requested lead time starts from order confirmation, payment, or sample approval. This avoids comparing delivery promises that use different starting points.

Currency, Incoterms, and Payment Terms

Request quotations in the same currency and state the required payment terms. If using Incoterms rules, specify the rule, named port or place, and edition so suppliers quote on a consistent delivery basis.

Ask for quote validity, minimum order quantity, and separately stated charges where applicable. Require suppliers to state any deviations from the request and unresolved technical assumptions alongside the price.

FAQs

Can a Mill Request a Quote Without Sharing Its Full Recipe?

Yes, but the supplier still needs enough information to assess the application. Provide the fiber composition, process conditions, dye class, and relevant chemical types and dosages. If proprietary details cannot be disclosed, agree on what can be shared and identify the compatibility checks that remain necessary. Treat the recommendation as provisional until those checks are completed.

Does Higher Solids Content Mean Better Value?

Not necessarily. Solids content is not always the same as active content, and neither figure alone establishes application performance. Compare the quoted products at dosages that achieve the required result under the same conditions. Concentration data is useful supporting information, but it should not replace a performance trial.

What Should Happen if a Supplier Proposes Different Conditions?

Request a separate alternative quotation that identifies the proposed changes, expected benefits, and trial requirements. Keep it distinct from the quotation based on the original process so purchasing and production teams can assess both the chemical price and the operational implications.